Advanced Search

Power Crimp® 707 Crimper

Hoses & Fittings » Hose Crimp Equipment » Power Crimp Equipment

Images
Power Crimp Equipment - Gates - Power Crimp® 707 Crimper Power Crimp Equipment - Gates - Power Crimp® 707 Crimper Power Crimp Equipment - Gates - Power Crimp® 707 Crimper

Brand: Gates

The Gates Power Crimp 707 is the most precise, yet simplest crimper made.  It was the first crimper with electronic digital readout to indicate gauge setting.  The toughest part about using the 707 is pushing a button.  It takes just a few seconds to make factory-quality hose assemblies.  Crimps hydraulic hoses from low pressure return lines to extremely high pressure spirals, from 3/16" to 1 1/4" I.D.  Crimps straight and bent tube stems, plus 45° and 90° block types.

 

Below are the PC® 707 Die Selection Charts for MegaCrimp® and GlobalSpiral™ Couplings

For MegaCrimp® (G25) Couplings
Hose Type 1/4" Hose 3/8" Hose 1/2" Hose 5/8" Hose 3/4" Hose 1" Hose 1 1/4" Hose
M3K 721 or 731  722 or 732 733 734 735 737 ---
M2T 721 or 731 722 or 732 733 734 735 737 ---
G1 721 or 731 722 or 732 733 734 735 737 739
G2 721 or 731 722 or 732 733 734 735 737 739
For GlobalSpiral™ (G20) Couplings
Hose Type 3/8" Hose 1/2" Hose 5/8" Hose 3/4" Hose 1" Hose 1 1/4" Hose
EFG6K 733 733 735 735 737 ---
EFG5K 733 733 735 735 737 ---
EFG4K 733 733 735 735 737 739

Specifications

Dimensions: 13" wide by 12" deep by 26 1/2" high.
Maximum Working Pressure: 4900 psi
Production Rate: 100 assemblies per hour (using 1/2" I.D. two-wire straight thread assemblies).
Weight: 188 lbs.
The following accessories (in addition to any quantities specified in the table below) will also be added to your cart upon clicking "Add Items to Cart"
x  ~  - 
To see additional items, click the down arrow on Display Items or the NEXT tab.

Enter Qty Order # Description Note: Position
Enter Qty Order # Description Note: Position
Loading data from server.
JavaScript is not enabled in your browser. This page works best with JavaScript enabled.
7480-0043 Standard PC707 Crimper without dies - wired for 115 Volt Comes with a backup ring and a notched cone 10
7480-0046 Standard PC707 Crimper without dies - wired for 230 volts Comes with a backup ring, a notched cone and a no-notched cone 20
7481-0023 Power Source - 115 volt, 30 amp, circuit, 1 h.p., 60 cycles 30
7481-0028 Power Source - 230 volt, 15 amp, 1 h.p., 60 cycles 40
7482-1217 721 Die Set 50
7482-1218 722 Die Set 60
7482-0931 731 Die Set 70
7482-0932 732 Die Set 80
7482-0933 733 Die Set 90
7482-0934 734 Die Set 100
7482-0935 735 Die Set 110
7482-0937 737 Die Set - must use No-Notch Die Cone 120
7482-0939 739 Die Set - must use No-Notch Die Cone 130
5
Power Crimp® 707 Crimper
You did not type the words correctly. Please try again. If the words are illegible, hit the rotating arrows icon to use a different set.
* Required
Success
Your message has been sent! Thank you for your inquiry.
A customer service representative will contact you as soon as possible.